See also TC2050-IDC-NL (no-legs) version with a tiny 0.03” footprint. This 10-conductor cable has a TC2050 Tag-Connector on one end and a standard 0.1" ribbon connector on the other and is suitable for use with most many MCUs / FPGAs and JTAG programming and debug operations. The legged version footprint takes about the same board space as two or three SMT resistors which means you can locate the footprint right next to the MCU if desired.
![usb download cable jtag spi programmer for lattice fpga cpld usb download cable jtag spi programmer for lattice fpga cpld](https://ae01.alicdn.com/kf/HTB1YBaKM9zqK1RjSZFpq6ykSXXad/USB-Isp-Download-Cable-JTAG-SPI-Programmer-for-LATTICE-FPGA-CPLD-Development-Board-Support-Windows.jpg)
Requires only a tiny footprint of pads and locating holes in your PCB.Tag-Connect's TC2050-IDC "Legged" Plug-of-Nails™ programming cable is a 10-conductor cable fitted with a spring-pin Tag-Connector that conveniently plugs directly into your PCB and terminates in a 0.1" ribbon connector.
![usb download cable jtag spi programmer for lattice fpga cpld usb download cable jtag spi programmer for lattice fpga cpld](https://ae01.alicdn.com/kf/H7cf2d394b4164db98d49caf25d93f8b2j/Lattice-ispDownload-Cable-USB-Jtag-ISP-FPGA-CPLD-Programmer-for-Diamond-ispLever-Win7-WIN8-WIN8-1.jpg)
This 10-conductor cable has a TC2050-NL Tag-Connector on one end and a standard 0.1" ribbon connector on the other and is suitable for use with most many MCUs / FPGAs and JTAG programming and debug operations.Ī growing range of adaptors are available for specific and generic applications such as Xilinx SPARTAN and VERTEX FPGAs, TI MSP430 ( TC2050-IDC-430), etcĪlso available in self-retaining "legged" version TC2050-IDC. The tiny "No Legs" footprint takes only 0.03 square inches (about the same board space as a couple of SMT resistors) which means you can locate the footprint right next to the MCU if desired. Instead, Tag-Connect uses tried and tested spring-pins rated for over 100,000 operations to make a secure connection to a special footprint pattern of pads and locating holes in your PCB. Tag-Connect uses a specially designed (Patent Pending) connector which eliminates the need for putting a programming header or other mating connector on every PCB. Tag-Connect cables provide a simple, reliable means of connecting Debuggers and Programmers or other test equipment to your PCB's while lowering board costs and facilitating efficient production programming.
![usb download cable jtag spi programmer for lattice fpga cpld usb download cable jtag spi programmer for lattice fpga cpld](https://i.ebayimg.com/images/g/qTwAAOSwnKdbZRK9/s-l300.jpg)
* 500 Ohm Resistor fitted on back of Adapter PCB between VCC and GND 1 x TC-LATTICE Note: Adapter only, Lattice HW-USBN-2B and Tag-Connect TC2030-IDC cable not included! See also our TC-LATTICE-10 adapter for TC2050-IDC 10-pin target board connectors. This resolves the issue of the Lattice HW-USBN-2B unexpectedly raising VCC on low-power targets and eliminates the need for the resistor to be fitted to each of your target PCB's - see. The adapter has a 12-pin (2圆) 0.1" female header that plugs into the Lattice HW-USBN-2B programmer and supplies a 6-pin (2x3) 0.1" male box header suitable for use with Tag-Connect TC2030-IDC Plug-of-Nails™ Cables, eliminating the need for a physical connector on each and every target PCB.īy default, the TC-LATTICE adapter comes fitted with a 500 Ohm resistor connected between VCC and GND. The TC-LATTICE Adapter allows users of Lattice's HW-USBN-2B Programming Cable to use Tag-Connect TC2030-IDC or TC2030-IDC-NL cable instead of the supplied flying lead solution for programming various Lattice Semiconductor devices.